0.7-1.5mm High Frequency Welded Pipe Mill 90m/Min

HG32 High-Frequency Welded Pipe Production Line is designed to produce welded pipes of Ф16～45mm in diameter and 0.7～1.5mm in wall thickness as well as square and rectangular pipes and deformed pipes of the corresponding size. Adopting roll pass design, the production line can manufacture welded steel pipes with good quality machining and high precision assembling.

According to the designing guideline of improving the operating character & environment and the safety & producing character , reducing the cost of the roller to guarantee high efficiency,HG32 production line adopts the double-radius hole style of design .

Main Parameters and Specifications:

1. Material Specifications:

Conforming to the YB189-64 standard

Material : Low carbon steel and low alloy constructional steel

• Mechanical properties: σ_b≤520Mpa,σ_s≤365MPa
• Strip Width:50～140mm
• Strip Thickness:0.7～1.5mm
• Inner Diameter of Coils:φ480～φ520mm

Outer Diameter of Coils:φ1000～φ1500mm

Coil Weight:≤2T

2. Welded Pipe Specification:

(1) Round Pipe Diameter:φ16～φ45mm

(2) Wall Thickness of Pipes:0.7～1.5mm

(3) Fixed Cutting length:4～9m

(4) Pipe-cutting Precision:0～3mm

3. Forming Speed:30～90m/min

4. Power, Water & Air Supply

1. Uncoiler

The uncoiler is of the structure of double expansion and cantilever mandrels. It contains two main parts: main body and the fixed base. The main body is equipped with pneumatic system to satisfy the needs of expanding, contracting and braking of the mandrels.

There are two mandrels on the main body. Each mandrel consists of four-bar linkages that could move radially at the same time. The four-bar linkages in two groups are fitted on two shafts respectively. Powered by air cylinder, they expand and contract radially. When one mandrel is uncoiling , the other one on the other end contracts to load a new coil and sustain it by expansion, which is then fitted with shield arm on the mandrel to prevent the coil from loosening during uncoiling. When the uncoiling operation of the mandrel in working is finished, pull down the positioning pin shaft and turn the mandrel for 180°manually. Then push the pin shaft back to its positioning slot. Now the new coil is in the working position. The cycles repeat in this way.

2. Cutting & Welding Machine

Cutting & Welding Machine is used to cut the irregular ends of the strips and then connect the strips by welding.

3. Horizontal spiral accumulator unit

This unit is main include in press& carry material device, accumulator assemble, carry off material unit, electric control unit.

(1)press & carry material device:It is main include frame, electric motor, brake unit, circling direction transfer power axle of the reduce velocity, press & carry roll, pressure air system of guide roll, inspected velocity unit; it can supply the strip steel to accumulator and the mean times it will transfer the carry velocity information to electric control system, when we demand stop carry the material to this unit, it will stop roll to the electric motor and press& carry material roll by the break, and also could adjust the velocity to carry electric motor and the unit carry material velocity.

(2)Accumulator frame assemble: include the electric motor, frame , inner circle roll, out circle roll and pressure roll. It can be used to storage the strip steel material from press& carry unit and it could be draw from the center send-off material roll.

(3)Send-off material device: include frame, guide direction rolls, guide out roll of high or lower place. It can carry the strip steel to shape system and send the carry out material velocity information to electric control device.

(4)technical parameters:

working style:change circle

advantage:storage material more, no strike to strip steel suface.

steel coil thickness:0.7-1.5mm

width:50-140mm

storage area:3.0 m2

carry material going velocity:Vmax=240m/min

Pinch form:pneumatic 6Mpa

electric motor power of the press & carry:11KW

the electric motor of the accumulator frame :15KW

4. Forming & Sizing Mill

Forming & Sizing Mill adopts roller type forming principle and high-frequency induction welding. The strip is fed into the forming machine by the feeding device in the mill and the forming roller continuously rotate and press the strip into the required shape. Due to the skin and the kindred effect, the high-frequency current is concentrated on the weld joint that is heated rapidly and reaches the welding temperature. The tube seam is welded under the pressure of squeeze rollers. The finished welded tube with required size can obtained after the cooling, sizing and primary straightening.

5. Cutting saw machine

Cutting saw machine is used to precisely cut the pipe to length automatically under the condition that the pipe continuously delivered from the mill at high speed.

6. Roll Table, Bench & Packing Machine 

The finished pipes run along the Roll Table and to be automatically moved onto the Bench. Then simple Packing Machine packs the pipes in hexagon shape.

The simple packing machine contains container and pneumatically driven alignment equipment.

Motor of Roll Bench: 3KW.

7. Roller :

The material :Cr12