|
Product Details:
Payment & Shipping Terms:
|
Product Name: | Fully Automatic Thickness 3-16mm Square Erw Pipe Mill | Steel Strip Width: | 270-800mm(±0.2mm) |
---|---|---|---|
Square Tube: | 80x80—200x200mm | Running Speed: | 10-30m/min |
Product Thickness: | 3-16mm | Mode Of Production: | Full Automatic |
Warranty: | One Year | Welding Type: | High Frequency Welding |
Cutting Saw: | Milling Saw | Keywords: | Square Erw Pipe Mill |
Highlight: | erw pipe mill fully automatic,precision industrial tube mills,square pipe erw welding machine |
Raw material, finished product, process, and user configuration profile
1,Raw Material Conditions:
(1) Hot rolled or cold rolled steel strip (meet GB700-88,GB1591-88)
Yield strength of raw material:σs≤345Mpa
Tensile strength of raw material :σb≤560 Mpa
(3) Thickness of strip: square pipe Thickness 3-16mm(GB708-88)
(4) steel strip width:270-800mm(±0.2mm)
(5) steel coil inner diameter:Φ508-Φ760mm
(6) steel coil out diameter:Φ1100-Φ2000mm
(7) max coil weight:16TON
2,Pipe size range:
(1) square tube: 80x80—200x200mm
(2) product thickness:
square and rectangular pipe:3-16mm
Power supply: 380V 50Hz 3 PHASE
3,product process
Raw material (strip) -loading car--- uncoiler - Cutting and Welding- feeding - Storage material - passive leveling - forming rolling--high frequency welding -- remove the weld burr -----cooling --sizing-- coarse straightening - length cut - collection
The main equipment introduction
The loading car is used for make the steel coil from loading position to uncoiler.at the same time loft oil cylinder,so that the steel coil inner hole is accurately set on the cone of uncoiler, after the uncoiler tension, push back to the original position.
Coil OD: Φ1100~Φ2000 mm
Coil ID: Φ508-Φ760mm
Width: 270~800mm
Running speed: 4 m/min
Running stroke: 3.5m
Transmission motor power: AC4KW(Double chain drive)
Lifting hydraulic cylinder diameter×stroke:Φ200×650 mm
hydraulic system working pressure:8~10 MPa
Up push strength: 16 T(6MPa)
Max coil weight: 16T
Single spindle hydraulic expansion and contraction type reel, the roller is sliding block type, with support, double disc brake, two brakes,
Drum diameter: Φ508 mm -Φ760 mm, uncoiler machine has a horizontal control function, can adjust the overall width direction.
technical parameters
coil out diameter:Φ1200-Φ2000mm
coil width:270-800mm
coil max weight:16Ton
cone move method: hydraulic
cone type: hydraulic expansion
cone move hydraulic cylinder shaft diameter:Φ140/Φ100 mm
Main motor AC7.5KW
Uncoil speed: 6m/min
Unwinding drive chain model 28A-2
Brake type:Pneumatic
Brake model: 2× DBH205
Clutch opening and closing method: pneumatic
Clutch opening and closing cylinder bore Φ125 mm
The straight-head device and the shovel are matched with the decoiler to disassemble the steel belt head, and send the steel belt into the straight-head pinch leveling machine. The blade is matched with the straight-head pressure roller to straighten the head of the steel strip and then the steel strip is sent to the pinch roller.
Technical parameters:
width 270~800mm
thickness 3~16mm
Shovel telescopic cylinder:Φ125/Φ90mm
Blade swing cylinder: Φ125/Φ90mm
Blade material: 50Mn
Pressure roller swing cylinder Φ140/Φ100mm
Roller drive form
Hydraulic motor
Hydraulic motor model 1QJM32-32Z3
Straight roller cylinder Φ100/Φ70mm
Straight head device swing arm: Adopt welded box structure
Shovel device: Use vertical blade
Straight-head device, pressure roller and shovel, cooperate with the decoiler to disassemble the steel strip head, and send the steel strip to the pinch leveling machine. The pinch roller is hydraulically pressed to clamp the steel belt, and the main motor is rotated to send the steel belt to the pinch roller. After the steel belt enters the pinch leveler, the leveling roller is pressed down to a suitable position to level the steel strip Flat, and send the steel strip to the shearing butt welding machine, and cooperate with the shearing butt welding machine to complete the shearing butt welding.
Technical parameters :
width 270~800mm
thickness 3~16mm
pinch motor AC30KW(Frequency)
positive pinch leveling speed ~7m/min
Pinch roller form and reduction :Two-roller type, hydraulic pressure
Pinch roller press down the cylinder Φ160/Φ110mm
Pinch roller diameter×length Φ280×850mm
Pinch roller material 42CrMo
Transmission form of pinch roller and leveling roller:Pinch up and down rollers are fully active, and leveling rollers are active underneath
Passive pinch leveling speed ≤30m/min
Leveling roll form and reduction
Upper two-lower three-roller type, hydraulic pressure
Leveling roller press down cylinder Φ200/Φ160mm
Diameter of Leveling Roller×Length Φ200×850mm
Leveling roller material 42CrMo
Roll quenching hardness and depth HRC52~58, depth:3~5mm
Vertical roll diameter×height Φ200×300mm
Vertical roller structure: I-shaped double vertical roller
Vertical roller material 42CrMo
Roll quenching hardness and depth HRC52~58,depth:3~5mm
Vertical roller width adjustment motor 2 ×AC2.2KW
Clutch opening and closing method : pneumatic
Clutch cylinder bore: Φ125mm
Used to cut off the irregular part of the tape head and tail, and align the tape tail of the previous coil with the tape head of the next coil, and weld them together to continuously feed the looper.
Structural form: shear welding bed, pinch feeding device, double centering device, double shearing shearing system, shearing plate system, welding bottom plate driving system, etc.
Technical parameters :
steel strip thickness:3-16mm
steel strip width:270-800mm
steel strip strength:
σb≤520Mpa;σs≤350Mpa
cutting type: hydraulic
Compress type:hydraulic
welding type : by motor AC0.55KW
hydraulic working pressure:10Mpa
welding speed: 0.4~0.6 m/min
Cutting method: Guillotine hydraulic shears
Shear structure form : Double Scissor Blade
Cutting edge material: 6CrW2Si
Butt welding clamping cylinder:
Ф125/Ф90mm
Pinch roller materia:l 42CrMo
Pinch form: Lower roller active
Pinch down cylinder Ф125/Ф90mm
pinch speed: ~5m/min
pinch motor: AC15kW
Clutch opening and closing method : pneumatic
Clutch cylinder bore :Φ125mm
This machine is between shear welder and host (forming sizing mill) ,use for after a roll of strip steel are used up, before the next roll strip since prepared from uncoiling, shearing and butt welding time to ensure that the host (forming sizing mill) continuous production and store enough strip steel.
This unit is main include in press& carry material device, accumulator assemble, carry off material unit, electric control unit.
(4)specification:
diameter:14m
accumulator type: External feed and internal delivery
steel coil thickness:3-16mm;width:270-800mm
carry material going velocity:Vmax=80m/min
feeding motor power:AC 132kw
storage motor: AC 17.5KWx17SET
Storage area:5m2
Forming 12 stand, sizing 4 stand , turkey head 2 stand
Cut the running steel tube into the following runout table.
When the continuous working rolling mill delivers the steel pipe to the flying saw, the saw car tracks and synchronizes with the pipe speed, the clamp block clamps, and the two saw cutting systems installed on the rotary table with the saw blade rotation, which makes radial feed under the drive of the feed ac servo motor.At this time, the rotary table is also rotating, and the saw cutting system makes compound movement between the rotary table and its own feed, and cuts the steel pipe along the section shape track of the cut piece.Then the systems relax back into place and wait for the next working cycle.The cutting feed use polar coordinates type.
equipment composition:
Body system, sawing machine, driving system, rotary disk system, feed system, jig, roller device, speed measurement device, hydraulic system, control system
basic parameters:
square pipe size:80x80--200x200mm
steel strip thickness:3~16mm
Steel strip material:carbon steel,Pre-galvanized hot rolled strip, cold rolled strip
Cut length:4-12m
Cut accuracy:≤2mm
Cutting type:double saw blade, rotate milling cut
Tracking speed:same as tube mil l(10-30m/min )
Equipment function:automatic,manual,It has the function of cutting short length
The short length bigger than 6m.
Control type: Siemens AC servo location
Feeding direction:according to customer require
machine parameters:
Cutting motor:servo AC14kw
Feeding motor:servo motor AC3.5kw one set
Drive motor: DC45KW
Clamp type:hydraulic
The saw bed,sawing machine,rotary disk system and cutting system with annealing treatment.
Guide line quantity 4,Taiwan shangyin brand or Nanjing
electric parameters:
touch screen | HMI | 1 | Siemens |
motion controller | PLC | 1 | Siemens |
Bearings | NSK/SKF | ||
Main electrical components | Siemens | ||
hydraulic valve | Beijing Huade | ||
oil pump | Shanghai | ||
oil cylinder | Domestic (Fushun) |
Function description:
Counting, palletizing:After the number of steel pipes reaches the specified number, the entire layer of steel pipes will be sent to the material frame by the layer sucker mechanism, according to the set package type, after the stacking is completed, the entire package of steel pipes will be transported to the packing rack.
Strapping:The package transfer roller table is started, and the whole package of steel pipes are moved out of the palletizing station and transferred to the strapping station; automatic packaging and welding are completed, and the water is controlled at the same time.
Traverse:The side rollers are opened, and the bundled steel pipes are removed. Reach the weight measurement position.
cycle:After the whole package of steel pipes are removed, the lifting platform returns to the receiving position and waits for the stacking of the next package of steel pipes. The stacking connection between each package of steel pipes realizes seamless docking to ensure the continuity of work.
The electrical control adopts PLC program control, touch screen (PLC adopts German Siemens), realizes man-machine dialogue, can freely switch between manual and automatic, and the electrical components use Delixi brand. In the program, you only need to input the number of steel pipes per layer, the number of layers of each bundle of steel pipes and the necessary parameters. After adjustment, the baler will automatically stack the required complete package of steel pipes.
Note: After the device is automatically reset to zero every time it is started, it performs a self-check. After the device is in a normal state, it can be officially operated.
Technical parameters of automatic strapping machine
Deduction method: no deduction, four deduction positive and negative deduction
Buckle strength: up to 70% of the base material of the strapping tape
Transmission mode: feeding and rewinding frequency conversion brake motor
Tension range: 15KN adjustable
Threading speed: 90m/min
Strapping speed: 23 seconds/cycle (related to the size of the bag)
voltage: 380V/50HZ
control voltage :DC24V
Power consumption : uncoil1.5KW ; head1.5KW
The main components:
No. | Name | Quantity | Notes |
1 | Rotary feeding | 5sets | Motor drive 7.5KW |
2 | Step feeding | 5sets | Motor drive7.5KW |
3 | Counting single push layer push system | 5sets |
Motor drive4.5KW servo motor |
4 | Lifting palletizing system | 5sets | 2set motor drive 7.5kw servo |
5 | Align the ends | 1set | Cylinder model 100x500 |
6 | Transfer trolley | 5sets | motor 2.2kw |
7 | Automatic strapping | 1set | |
8 | Roller conveyor | 8sets | 2.2kw motor |
9 | Storage bag | 4sets | 4KW Motor |
10 | Electric control system | 1set | plc taida PLC |
11 | Hydraulic station | 1set | 7.5kw motor |
10)Rollers material: Cr18-20
11) 1200kw solid welder
Contact Person: Mr. Yan
Fax: 86-0311-8302-5332